하드디스크가 이상하다. 부팅이 잘 안된다. 버벅인다.

1
Your hard disk is a SAMSUNG HD103SJ with firmware 1AJ10001.
The average temperature for this hard disk model is 31°C (min=23°C max=42°C) and yours is 36°C.

  Attribute   Current   Raw
Raw Read Error Rate 100 000000000001
Throughput Performance 252 000000000000
Spin Up Time 72 000000002251
Start/Stop Count 99 000000000512
Reallocated Sector Count 252 000000000000
Seek Error Rate 252 000000000000
Seek Time Performance 252 000000000000
Power On Hours Count 100 00000000216E
Spin Retry Count 252 000000000000
Calibration Retry Count 252 000000000000
Power Cycle Count 99 000000000547
GSense Error Rate 100 000000000011
Power Off Retract Count 252 000000000000
Hardware ECC Recovered 100 000000000000
Reallocated Event Count 252 000000000000
Current Pending Sector 252 000000000000
Offline Uncorrectable Sector Count 252 000000000000
Ultra DMA CRC Error Rate 98 0000000004C2
Write Error Rate 100 000000000000
Load Retry Count 252 000000000000
Load Cycle Count 100 000000000547

All the attributes of your hard disk are above the S.M.A.R.T. thresholds set by the manufacturer. This is good.

WARNING : your hard disk Ultra DMA CRC Error Rate attribute current value (98) is below the normal range (98 - $issue.params[2]) reported for your specific hard disk model. This usually means that some communication errors occurred between the hard disk and the external controller. Most likely those errors are due to the cable. Double check it, reroute it and, if needed, replace it.

NOTE : your hard disk Power Cycle Count attribute current value (99) is below the normal range (100 - 100) reported for your specific hard disk model. Basically your hard disk was power cycled more times than the maximum number the average hard disk was. Power cycles put some stress on the hard disk mechanic. Sometimes power cycles can be caused by a loose hard disk power connector. Make sure it is properly fastened.

The overall fitness for this drive is 90%.
The overall performance for this drive is 88%.

------=-------
부팅도 잘안되고
부팅할때 디스크 검사도하고
별거 안했는데 디스크만 계속 읽는(버벅임) 등의 동작이 보여서 체크
-----=------
WARNING : your hard disk Ultra DMA CRC Error Rate attribute current value (98) is below the normal range (98 - $issue.params[2]) reported for your specific hard disk model. This usually means that some communication errors occurred between the hard disk and the external controller. Most likely those errors are due to the cable. Double check it, reroute it and, if needed, replace it.

대충 디스크 에러발생비율이 높다는 것.
대충 선이 문제있는거 아닌가? 라고 적혀있음.
그래서 전원 끝 후 SATA선 전부 뽑고 HDD0과 안쓰는 CD-ROM쪽의 SATA선과 바꿔서 꼽음.

그런 후 효과
부팅이 빨라진 것 같다.
... 그외는 더 뒤져봐야지.
댓글
  • No Nickname
    No Comment
  • 권한이 없습니다.
    {{m_row.m_nick}}
    -
목록형 📷 갤러리형
3.31
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
4.25
4.26
4.27
4.28
4.29
4.30
5.1
5.2
5.3
5.4